供以下消息类型:系统故障、过程报警、开关动作和操作员提示。可为过
程消息类型指定不同的优先级(从0~5)，系统故障另分成三个优先级(SI ~S3).不同优先级的消息
以不同的颜色显示并可选择不同的确认方法。此外还显示过程点的名称和故障状态。所有消息均可
以中文显示，同时可发出声音。
消息行
二，
各种显示画面的项部区均为消息行，用以对来自整个重重雪
过程的各种不同消息类型进行更高-级的显示。消息行显
示最末或最先的5个消息，以及消总确认和操作员提示调
出按钮。消息行还有消息容量溢出指示区和未确认消息个
数显区.
一.1:
故障过程点的面板窗口可从消息行直接调出以便快速操作。
消扈一览衰
消息一览表显示列出了所有当前消息的概况，它按时间先后顺序列出了发生的过程报警、开关动
作以及系统故障等不同类别的消息。最末产生的消息在消息一览表的消息一 -览表 显示列出了所有当前
消息的概况，它按时间先后顺序列出了发生的过程报警、开关动作以及系统故障等不同类别的消息。
最末产生的消息在消息- -览表的首行或尾行。消息的时间排序方式(升序或降序)可以在线更改。同消
息行一样，不同的优先级的颜色不同。消息可成块确认或整页确认。
为观察更加清晰，操作员可把某个优先级或装置区域的消息暂时从屏幕上取消而不显示。消息-
览表的容量大小由组态决定，如果当前的消息数目超过所组态的容量规模，则先进入的消息被删除，
以让出空间给当前消息进入。
操作员提示览表
对于每个过程报警消息和开关动作消息均可组态相应的操作员提示。该提示可以通知操作员消息
出现的原因及为消除故障应采取的相应措施等内容。如果需要该提示还可为操作员提供更多的帮助。
操作员提示一览表显示列出了所组态的全部提示。同时可发出提示声音(如人声) .
记录
记录用于记录来自过程的事件.状态和顺序。记录文件可存贮在硬盘上，可在监视器上显示、通
过打印机输出或存储到软盘上以备将来评估。
另外记录文件可自动通过FTP协议发送到以太网上的任何节
点。可使用Industrial”系统的数据浏览软件Digi Browse观察
这些数据或转换成ASCII码文件。
Industrial”系统有以下记录类型:
信号顺序记录(SOE)
信号顺序记录用于记录各种事件，如过程和系统报警、开关动作消息、操作员干预和提示。组态
时可确定所要记录消息的优先级。操作员可从信号顺序记录中获知事件发生的先后顺序，分辩率1毫
秒
生产报表记录
生产报表记录是指在–定的时间间隔内或在某种情况下，记录下过程变量的当前值或状态。该记
录可周期性运行(如班报、日报、月报等)，也可手动启停或由事件驱动启停。
事故迫忆记录
事故追忆记录用于检查分析事故的详细过渡过程(脉络波形)。为实现这–目的，系统以极高的时
间分辨率(间隔最小5亳秒)采集事故发生(某开关变量状态改变)前后几分钟有关模拟变量的测量值，
并存储在操作站中。
系统诊1就亚不
系统硬、软件的当前状态由-一个在后台自动运行的系统诊断程序进行监视。
诊断显示的结果在标准化系统显示中分三个详细层次进行描述:
系统状态显示(显示包括操作站、过程站、现场控制器以及系统总线DigiNetS 和站总线
DigiNetP在内的系统结构总貌和状态)
●站状态显示(显示 某站的状态信息)
●模件状态显示(显示与所选模件有关的详细信4)。
5. 3系统工程组态与调试维护工具软件CBP (Control Builder F)
CBF:是Industrial “DCS控制系统的工程工具，它是集组态(包括硬件配置、控制策略、HIS即人机
接口等组态)、工程调试和诊断功能为- -体的工具软件包。CBF采用统- -的 系统全局数据库和强大的交
叉参考工具，不仅能方便地完成自动化组态，而且是一个高性能的过程调试工具。Industrial”DCS系
统过程控制站PS所需的各种控制算法和策略都是由CBF来组态的，井采用图形化的组态方法(符合
1EC61131- 3标准)。
CBF也用于对操作站人机接口(HIS)功能的组态并还可直接对现场总线设备进行组态。
控制算法和策略组态可选用以下IEC 61131-3标准组态方法中的一-种或几种:
FBD (功能方块图 )
JD (梯形图)
SFC (顺序功能图 )
IL (指令表)
sT (结构化文本)
CBF安装在Industrial “系统工程师站上，完成后的组态结果由工程师站通过系统网络下载至相应
的现场控制器PS及操作站0S中。组态既可在线也可离线。离线组态仅需-台装有CBF软件的计算机。
系统提供-一个含有220多种功能模块(标准算法程序)的功能块库，除了IEC 61131 _3 标准规定
的基本内容外，还扩充了许多功能强大并经过严格测试的功能块。用户还可自定义功能块和由若千功
能块组成的用户宏。CBF 还提供200 多个标准图形符号(静态和动态)及大量美观实用的立体图例可
供HIS组态选用。
CBF在执行组态编译时能自动查找定位错误源，交叉参考功能可帮助工程师迅速查找对应的变
量位号、功能块及操作画面，大大提高了组态效率。CBF可引入或导出ASCII 程序、显示画面、变
量位号和部分项目树。CONTROL BUILDER F还可输出包括全部组态结果的图形化工程文档。
CBF (Control Builder F)还具有如下特点: .
o使用同一工
PP826-3BSE042244R1
algorithm subroutines), in addition to the base specified in IEC 61131 3 standard
In addition to this content, many powerful and strictly tested function blocks from practical engineering applications are also expanded. Any complex control
All schemes can be realized by the combination of these function blocks.
The function blocks provided by the system mainly fall into the following categories:
o
Analog quantity processing
o
Digital quantity processing
Loop adjustment
Logical sequence control
c
Logical operation
Monitoring function
Acquisition function
c
Arithmetic operation
c
Tcp/ip protocol communication interface
Modbus protocol communication interface
1ec870-5 protocol communication interface (telecontrol)
4.2 field controller PS
Industrial ial “field controller PS is a special process control station, which is embedded with a fieldbus communication interface for users to use
Fieldbus technology provides a very flexible choice. Each PS is allowed to insert 4 fieldbus interface cards (card types can be different),
Each card is connected to a fieldbus to collect process data and diagnostic information from the bus. The interface card is easy to replace and plug and play
(plug & play) and can be plugged in and out with power.
The field controller PS has the following features:
o
Flexible: it supports all international standard open fieldbus and can be mixed
4 high-speed fieldbuses can be connected at the same time (max. 12 MBD)
Simple project: only use the same tool CBF (control build f) software for configuration, debugging and diagnosis
mouth
Access to all information from the site, including equipment management information
Global database of Fieldbus equipment, control level and HMI (human-machine interface)
Module identification with production operating parameters
c
Complete self diagnosis
Compact and rugged design
Front panel wiring
DIN rail (U-shaped) mounting well can be directly installed on the wall, which is simple and convenient
o
Allowable operating ambient temperature 60 C, automatic temperature monitoring
o
EMC (electromagnetic compatibility) conforms to en50082 standard
mouth
Certification: CE, Namur, CSA, csa-nrtl, FM class 1 div2, ghost, Lloyd
Installation area: Class 1 div 2
The PS supports the following types of fieldbus standards:
Profibus DP，up to 12 MBd
Modbus RTU，1200 to 38. 4KBd
Industrial” CAN I/0 Bus
o
Open CAN -Bus，up to 1 MBd
o
Foundation Fieldbus H1
up to 31. 25KBd
Foundation Fieldbus H2 (fast Ethernet)
HART
The system allows different types of field buses to be mixed and run simultaneously in the same field controller PS.
Industrial “field control explosion (AC800F) consists of the following components:
Basic unit pm802f
Power supply sa801f/sd802f
o
Ethernet network card ei801f/ei802f/ei803f
o
Fieldbus interface card fi810f/fi820f/fi830f
Various accessories
The main components of the field controller PS are described below.
Basic unit pm802f
The basic unit pm802f is composed of a metal rack and a CPU motherboard. It periodically scans the data from the
The signals of the field bus sensors are processed according to the control application program configured by the user, and then the calculation results are passed
The fieldbus interface card returns the corresponding fieldbus actuator.
Two field controllers can realize controller 1:1 redundancy, and undisturbed switching between master and slave PS. Two on each PS
Ethernet network card, the second network card is used to connect the system network diginets), and the second network cards can be interconnected with each other to form a special
Redundant communication link (diginetr) to ensure information synchronization between master and slave PS. — However, the master PS fails, and the slave PS can quickly and undisturbed connect the replacement worker
Make. All inputs and outputs also support redundant operation.
The data communication between the field process controller PS. operating station 0s and the engineer station es is completed by the system network (diginets), which is inserted
The – Ethernet network card on the PS basic unit provides the interface between PS and diginets. ES. Hardware configuration and PS
The user program is downloaded to the PS CPU through diginets and the first network card. After the field bus interface card is newly installed or replaced, the required group
The status information will be automatically reloaded. The configuration results and real-time process data are stored in RAM, and ram is installed on the Ethernet network card or battery card
The backup battery can maintain the configuration content and data in case of power failure.
Basic unit pmbo2f characteristics:
mouth
Installation slots of 4 fieldbus interface cards
c
Installation slot of 2 Ethernet network cards
Support redundant operation of Fieldbus interface card
Support hot plug of Fieldbus interface card
Technical indicators of basic unit pib02f:
CPU :Intel 80960HT25/75
32-bit RISC superscalar processor with operation speed of 150 MIPS
4 MB FLASH-EPROM
E
PP826-3BSE042244R1
